Shenzhen Handar Optical Technology Co.,Ltd
Shenzhen Handar Optical Technology Co.,Ltd Details determine success or failure, choose the future of success
Add to Cart
Product Features
1. Product Description
The HD-SFP+/10G-ZR is a 10Gbps enhanced small form factor pluggable SFP+ transceiver compatible with 10GBASE-ZR/ZW. It is suitable for 80km single-mode fiber (SMF) communications in 10Gbps Ethernet.
2. Regulatory Compliance
Handar transceivers are Class 1 Laser Products comply with FDA regulations. Meet Class 1 eye safety requirements of EN 60825 and the electrical safety requirements of EN 60950.
3. Absolute Maximum Ratings
| Parameter | Symbol | Min. | Max. | Unit |
| Supply Voltage | VCC | -0.5 | 4 | V |
| Storage Temperature | TS | -40 | 85 | °C |
| Operating Case Temperature | TC | -5 | 75 | °C |
| Power Received Max | Pmax | -7 | dBm |
4. Recommended Operating Conditions
| Parameter | Symbol | Min. | Typical | Max. | Unit | |
| Operating Case Temperature | TC | -5 | 75 | °C | ||
| Power Supply Voltage | VCC | 3.15 | 3.3 | 3.45 | V | |
| Power Supply Current | ICC | 450 | mA | |||
| Data Rate | 10 | GBps | ||||
| Max Link Length on 9/125µm SMF | CLSFPP1510GZR | Lmax | 80 | km | ||
5. Optical Characteristics
| Parameter | Symbol | Min. | Typical | Max. | Unit | |
| Transmitter | ||||||
| Centre Wavelength | λc | 1530 | 1550 | 1570 | pm | |
| Spectral Width (RMS) | σ | 3 | nm | |||
| Average Output Power | CLSFPP1510GZR | Pout | 0 | 5 | dBm | |
| Extinction Ratio | ER | 8 | dB | |||
| Average Launch Power of Off Transmitter | Poff | -30 | dBm | |||
| Receiver | ||||||
| Centre Wavelength | λc | 1200 | 1600 | nm | ||
| Receiver Sensitivity | PIN | -25 | dBm | |||
| Receiver Overload | Pmax | -7 | dBm | |||
| LOS De-Assert | LOSD | -30 | dBm | |||
| LOS Assert | LOSA | -35 | dBm | |||
| LOS Hysteresis | 0.5 | 4.5 | dB | |||
6. Electrical Characteristics
| Parameter | Symbol | Min. | Typical | Max. | Unit |
| Transmitter | |||||
| Input Differential Impedance | Zin | 90 | 100 | 110 | Ω |
| Data Input Swing Differential | Vin | 250 | 1200 | mV | |
| Tx-Dis Disable | Vd | 2.0 | Vcc | V | |
| Tx-Dis Enable | Ven | 0 | 0.8 | V | |
| Receiver | |||||
| Data Output Swing Differential | Vout | 250 | 800 | mV | |
| Rx-Los Fault | Vlf | 2.0 | VccHOST | V | |
| Rx-Los Normal | Vln | 0 | 0+0.8 | V | |
| Output rise and fall time | Tr, Tf | 30 | ps | ||
7. Pin Descriptions
| Pin | Symbol | Description | Ref. |
| 1 | VEET | Transmitter Ground (Common with Receiver Ground) | 7.1 |
| 2 | TFAULT | Transmitter Fault. Not supported. | |
| 3 | TDIS | Transmitter Disable. Laser output disabled on high or open. | 7.2 |
| 4 | MOD_DEF(2) | Module Definition 2. Data line for Serial ID. | 7.3 |
| 5 | MOD_DEF(1) | Module Definition 1. Clock line for Serial ID. | 7.3 |
| 6 | MOD_DEF(0) | Module Definition 0. Grounded within the module. | 7.3 |
| 7 | RS0 | Rate Select0, optionally controls SFP+ module receiver. When high input signaling rate>4.25 GBd and when low input signaling rate<4.25GBd | |
| 8 | LOS | Loss of Signal indication. Logic 0 indicates normal operation. | 7.4 |
| 9 | RS1 | Rate Select1, optionally controls SFP+ module receiver. When high input signaling rate>4.25 GBd and when low input signaling rate<4.25GBd | |
| 10 | VEER | Receiver Ground (Common with Transmitter Ground) | 7.1 |
| 11 | VEER | Receiver Ground (Common with Transmitter Ground) | 7.1 |
| 12 | RD- | Receiver Inverted DATA out. AC Coupled. | |
| 13 | RD+ | Receiver Non-inverted DATA out. AC Coupled. | |
| 14 | VEER | Receiver Ground (Common with Transmitter Ground) | 7.1 |
| 15 | VCCR | Receiver Power Supply | |
| 16 | VCCT | Transmitter Power Supply | |
| 17 | VEET | Transmitter Ground (Common with Receiver Ground) | 7.1 |
| 18 | TD+ | Transmitter Non-Inverted DATA in. AC Coupled. | |
| 19 | TD- | Transmitter Inverted DATA in. AC Coupled. | |
| 20 | VEET | Transmitter Ground (Common with Receiver Ground) | 7.1 |
Notes:
7.1 Circuit ground is internally isolated from chassis ground.
7.2 Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.
7.3 Should be pulled up with 4.7k - 10kohms on host board to a voltage between 2.0V and 3.6V. MOD_DEF(0) pulls line low to indicate module is plugged in.
7.4 LOS is open collector output. Should be pulled up with 4.7k -10kohms on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.
8. EEPROM & DDM THRESHOLD
8.1 EEPROM
2 wire address 1010000X (A0h)
|
0~95 Serial ID Defined by SFP MSA (96 bytes) |
|
96~127 Vendor Speific (32 bytes) |
|
128~255 Reserved (128 bytes) |
EEPROM Serial ID Memory Contents
| Add. | Size (Bytes) | Name of Field | Hex | Description |
| BASE ID FIELDS | ||||
| 0 | 1 | Identifier | 03 | SFP |
| 1 | 1 | Ext. Identifier | 04 | SFP function is defined by serial ID only |
| 2 | 1 | Connector | 07 | LC |
| 3-10 | 8 | Transceiver | 00 00 00 00 00 00 00 00 | Transmitter Code |
| 11 | 1 | Encoding | 06 | 64B/66B |
| 12 | 1 | BR, Nominal | 67 | 10.3Gbps |
| 13 | 1 | Reserved | 00 | |
| 14 | 1 | Length (9um) km | 50 | 80km |
| 15 | 1 | Length (9um) km | FF | |
| 16 | 1 | OM2 Length (50um) m | 00 | |
| 17 | 1 | OM1 Length (62.5um) m | 00 | |
| 18 | 1 | Length (Copper) | 00 | |
| 19 | 1 | OM3 Length (50um) m | 00 | |
| 20-35 | 16 | Vendor Name | 43 2D 4C 49 47 48 54 20 20 20 20 20 20 20 20 20 |
C-LIGHT * OEM available |
| 36 | 1 | Reserved | 00 | |
| 37-39 | 3 | Vendor OUI | 00 00 00 | * OEM available |
| 40-55 | 16 | Vendor PN | xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx | * OEM available |
| 56-59 | 4 | Vendor Rev | 30 31 20 20 | 01 |
| 60-61 | 2 | Wavelength | 06 0E | 1550nm |
| 62 | 1 | Reserved | 00 | |
| 63 | 1 | CC_BASE | xx | Check Code for Base ID Field |
| EXTENDED ID FIELDS | ||||
| 64-65 | 2 | Options | 06 1A | Loss/ TX_Fault/ TX_Disable |
| 66 | 1 | BR, Max | 00 | |
| 67 | 1 | BR, Min | 00 | |
| 68-83 | 16 | Vendor SN | 43 4C xx xx xx xx xx xx xx xx xx 20 20 20 20 20 | SN of Transceiver (ASCII). Exp. “HDXXXXXXXXX” |
| 84-91 | 8 | Date Code | xx xx xx xx xx xx 20 20 | YY/MM/DD Exp. 120727 |
| 92 | 1 | Diagnostic Monitoring | 68 | |
| 93 | 1 | Enhanced Options | F0 | |
| 94 | 1 | SFF_8472 Compliance | 03 | |
| 95 | 1 | CC_EXT | checksum | Checksum for Extened ID |
| VENDOR SPECIFIC ID FIELDS | ||||
| 96-127 | 32 | Vendor Specific | 20 20 20…… | Depends on Customer Info |
| 128-255 | 128 | Reserved | FF FF FF…… | Depends on Customer Info |
8.1 DDM THRESHOLD
| Low Alarm | Low Warn | High Warn | High Alarm | |
| Temperature | -10℃ | -5℃ | 75℃ | 80℃ |
| Voltage | 3V | 3.1V | 3.5V | 3.6V |
| Tx Bias | 15mA | 20mA | 90mA | 100mA |
| Tx Power | -3dBm | -2dBm | 5dBm | 6.9dBm |
| Rx Power | -27dBm | -26dBm | -8dBm | -7dBm |
Ordering Information
| Part No. | Data Rate | DDM | Wave | Fiber Type | Dist. | Temp. | Optical Interface |
| HD-SFP+/10G-ZR | 10Gbps | yes | 1550nm | SMF | 60/80km | -5~75℃ | LC |
* WARNING: PLEAS KEEP THE RECEIVED POWER LOWER THAN -7dBm